Epoxy.com Product #318

This Product Has Been Superseded by Epoxy.com Product #641

EpoxySystems?? Product #641

Heat Resistant Epoxy Coating

 

DESCRIPTION

EPOXYSYSTEMS? PRODUCT #641 is a moisture-insensitive, two-component, 100% solids epoxy coating. EPOXYSYSTEMS? PRODUCT #641 is especially formulated to protect concrete, steel and wood subject to high temperatures and corrosion. EPOXYSYSTEMS? PRODUCT #641 has a convenient 1:1 by volume mix ratio and is easy to apply.

ADVANTAGES

EPOXYSYSTEMS? PRODUCT #641 is resistant to high temperatures (3000-4000F) in addition to its high chemical resistance.

bullet High chemical resistance to acids, alkalies and other chemicals
bullet Cure under high humid conditions
bullet High build
bullet Excellent hardness and gloss
bullet Not brittle
bullet No blush or exudation
bullet  High temperature resistance

USES

Wall and Floor Coating for:

bullet Food and beverage processing plants
bullet Meat and dairy processing plants
bullet Chemical plants
bullet Laboratories
bullet Aircraft hangars
bullet Jet engine test cells
bullet Plant maintenance coating
bullet Pipe coating
bullet Tank coating

 

PHYSICAL PROPERTIES

Working life

30 minutes (at 750F)

Cure Time:

  

Light traffic

24 hours

Heavy traffic

5 days

Tensile strength

8,500 p.s.i

Tensile elongation

3%

Compressive strength

14,500 p.s.i

Flexural strength

16,000 p.s.i

Impact resistance (1200 ft. lbs./in.)

0.041

Hardness, Shore D

83
Viscosity, CPS A Component 20,000 to 45,000
B Component 12,000 to 16,000
Mixed 14,000 to 17,0000

Linear shrinkage inches/inch

0.0033

 

CHEMICAL RESISTANCE

Chemical resistance - acids, alkalies, alcohols, acetone, cellosolves, toluene, Xylene and other solvents.

100% retention of flexural strength after two (2) weeks cure followed by seven (7) days immersion at 770F and 140"0F in the following:

Nitric Acid

45%

Sulfuric Acid

20%

Hydrochloric Acid

35%

Acetic Acid

35%

Sodium Hydroxide

50%

Potassium Hydroxide

50%

Sodium Hypochlorite

15%

SURFACE PREPARATION

Remove dirt, loose particles and oil contaminants by scarification, sandblasting. Then vacuum or blow clean with an oil free compressed air.

MIXING

Mix 1 part "A" Component with 1 part "B" Component using a low-speed, 1/2" mixing paddle for 3-5 minutes. Apply immediately. Apply by brush, roller or spray. May require heat for spraying. High temperatures will shorten pot life.

COVERAGE

125-150 square feet per gallon.

Force cures must be used for enhancement of high temperature and chemical resistant properties or to allow the coating to be placed in service before 5 days. Allow the coating a post cure of 12 to 24 hours before force curing.

RECOMMENDED FORCE CURE SCHEDULE
Minimum 4 hours @ 150oF
Minimum 6 hours @ 250oF

 

CAUTION

WARNING! "A" Component contains Epoxy Resin. "B" Component contains alkaline amines; strong sensitizer. May cause skin sensitization or other allergic responses. Avoid inhalation of vapor. Use good ventilation, particularly if the material is heated or sprayed. Prevent all contact with skin and eyes. Wear protective clothing, goggles, gloves, and/or barrier creams. If contact with skin occurs, wash immediately with water and contact a physician.

FIRST AID: In case of contact, immediately flush eyes or skin with plenty of water for at least 15 minutes. Remove contaminated clothing and shoes. Call a physician. Wash clothing before reuse. Discard contaminated shoes. Wear protective clothing, goggles, gloves, and/or barrier creams.

KEEP AWAY FROM CHILDREN

FOR INDUSTRIAL USE ONLY

Hit Counter